Line ID: @scnc (ต้องมี @ นำหน้า)

Brushless Servo Drives รุ่น ACS306 ขนาด 20-30VDC,6 A,10-180 W

฿2.00 ฿1
ราคายังไม่รวมภาษี 7% IntroductionThe DCS810 is a digital DC servo driver developed with DSP and high efficient MOSFET technologies. In position control, it\\\'s easy for
เหลือ 5 ชิ้น
ซื้อเลย
หยิบลงตะกร้า
  • หมวดหมู่ : เซอร์โวมอเตอร์ และไดร์ฟ
  • รหัสสินค้า : 000085

รายละเอียดสินค้า Brushless Servo Drives รุ่น ACS306 ขนาด 20-30VDC,6 A,10-180 W

ราคายังไม่รวมภาษีมูลค่าเพิ่ม 7% 

ราคายังไม่รวมค่าจัดส่ง EMS 80 บาท

Features

 

  • Advance DSP current control technology
  • Step & Dir, or CW/CCW control
  • High precision; smooth & quiet motor movement
  • Input voltage: 20-30 VDC
  • Continuous current: 6 A
  • Peak current: 15A
  • Capable of driving 10 - 180 W brushless servo motors
  • Electronic gear rate from 1/255 to 255
  • Built-in motion profile for servo tuning and testing
  • Small size, surface-mount technology

 

Description

Leadshine's fully digital AC servo drive ACS306 is developed with 32-bit DSP based on advanced control algorithm. Since its input commands are PUL/DIR signals, the users can upgrade stepping drives to the ACS306 without changing control systems. The ACS306 can offer high precision, high speed and high reliability performance, and widely used in inkjet printers, engraving machines, and etc. A built-in controller can be used for testing and tuning. PC based and handheld configuration & tuning tools can meet different tuning environments or requirements. The ACS306 can drive both DC brushless and AC servo motors. But it is more suitable for the DC brushless servo motors. Compare to ACS606, the ACS306 has smaller size and additional alarm (fault) signal output to indicate error.


* Pb-Free or CE/UL approved versions optional. Contact Leadshine or see more information in its hardware manual please.

 

Similar products

Specifications

 

Electrical Specifications (T= 25oC/77oF)

 

 

Parameters

ACS306

Min.

Typical

Max.

Unit

Peak output current

0

-

15

A

Continue output current

0

-

6

A

Supply voltage

+20

-

+30

VDC

Logic signal current

7

10

16

mA

Pulse input frequency

0

-

200

kHz

Isolation resistance

500

 

 

Mohm

Current provided to encoder

-

-

100

mA

 

Connectors

 

General Information

 

Feedback Signal Connector

Pin

Signal

Description

I/O

1

EA+

Encoder channel A+ input

I

2

EB+

Encoder channel B+ input

I

3

EGD

Signal ground

GND

4

HW

Hall sensor W input

I

5

HU

Hall sensor U input

I

6

FG

Ground terminal for shielded

GND

7

EZ+

Reserve

I

8

EZ-

Reserve

I

9

HV

Hall sensor V input

I

10

NC

Not Connected

-

11

EA-

Encoder channel A- input

I

12

EB-

Encoder channel B- input

I

13

VCC

+5V @ 100 mA max.

O

14

NC

Not Connected

-

15

NC

Not Connected

-

Control Signal Connector

Pin

Signal

Description

I/O

1

PUL+

Pulse signal input +

I

2

PUL-

Pulse signal input -

I

3

DIR+

Direction signal input +

I

4

DIR-

Direction signal input -

I

5

ENA+

Enable signal input +

I

6

ENA-

Enable signal input -

I

7

ALM+

Alarm(fault) signal +

O

8

ALM-

Alarm(fault) signal +

O

RS232 Communication Connector

Pin

Signal

Description

I/O

1

NC

Not connected

-

2

+5V

+5V power only for STU.

O

3

TxD

RS232 transmit.

O

4

GND

Ground.

GND

5

RxD

RS232 receive.

I

6

NC

Not connected

-

High Voltage Connector

Pin

Signal

Description

I/O

1

U

Motor phase U

O

2

V

Motor phase V

O

3

W

Motor phase W

O

4

+Vdc

DC power Input (20-30VDC)

I

5

GND

Power Ground.

GND

 

 

 

More about I/O Signals

 

Signal

Description

PUL+/PUL-

Pulse input signal. In single pulse (pulse/direction) mode, this input represents pulse signal, each rising or falling edge active (software configurable); 4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active at both high level and low level . For reliable response, pulse width should be longer than 0.85μs. Series connect resistors for current-limiting when +12V or +24V used. The same as DIR and ENA signals.

DIR+/DIR-

Directions input signal. In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (software configurable), this signal is counter-clock (CCW) pulse,active at both high level and low level. For reliable motion response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW.

ENA+/ENA-

Enable input signal. This signal used for enabling/disabling the drive. High level for enabling the drive and low level for disabling the drive. Usually left UNCONNECTED (ENABLED).

 

 

 

Typical Connections

 

Mechanical Specifications (unit: mm[inch])